Aluminum can be die casted, and it ranks among the most common metals for the process. Its low density, good corrosion resistance, and ability to fill thin, detailed shapes make it a strong choice for housings, brackets, and frames. Aluminum die cast prototypes also let engineers test a part in near-production material before they commit to volume. The details matter, though. High-pressure die casting, low-pressure casting, and gravity casting each suit different parts. In this guide, I explain how the process works, how to design for it, what it costs, and how I would pick a supplier for a robot shell.

That's about 2.7 g/cm³ for aluminum, which is about a third of what steel is. This keeps cast parts light while still making them strong enough to use. It has a thin layer of natural oxide that keeps it from rusting. It can also be used again and again and moves heat around well. It melts and forms thin walls and fine details. In other words, one casting can be used instead of several pieces that were welded or bolted together. It has these qualities that make companies that make robots, cars, electronics, and appliances want to buy aluminum castings. Robots need twice as much weight because a smaller shell puts less stress on the motors and joints. Of course, this is the main reason why shells, guns, and picture frames are often made of metal.
When you sand cast, you pour metal into a sand model that will only be used once. It can be used to make big or small parts, but the edges are rougher. A steel form that can be used over and over is used in permanent mold casting to make better surfaces and finer grain. You press metal into a steel mold to do die casting. When you use high-pressure die casting, metal is injected quickly, which is good for making a lot of parts with thin walls. The slab below is made with low-pressure casting. From below, the die is slowly filled up. The holding furnace is below the die, and gas pressure pushes the melt up a rising tube. Until the metal gets hard, the pressure stays the same. The extra liquid then falls back into the furnace.
A lot of people who buy things think that die casting is only good for big sales. That's not always right. You don't need full production tools on the first day because pilot or bridge tools can be used to make small engineering runs. What makes a process fit? It depends on the form, alloy, amount, tolerances, finishing, and testing needs. It is said that any casting method can use any aluminum alloy. For die casting under a lot of pressure, alloys like A380 are often used. A356 is often used for low-pressure and stable mold casting, on the other hand, since it works well with T6 heat treatment. Matching the metal to the process too early leads to changes that cost a lot more in the long run.

At the start of every job, the 3D CAD model, plans, GD&T callouts, wall thickness, draft, and service conditions are all looked over. It doesn't matter to me if the test is a sample assembly, a fit check, or a load test. I like to set the goal early on. The team then picks a metal based on how strong it is, how flexible it is, how resistant it is to rust, how easy it is to machine, and how many of them can be made. Making tools comes after the project stage. For small runs, bridge tools work best, trial tools for quick tests, and tools made for mass production for long runs. Before the steel is cut, you should agree with the supplier on the parting line, gate location, and machining datums. Now, a quick design for manufacturability (DFM) review keeps the work from having to be start over.
Aluminum die cast prototypes take five steps to cast something: melting, getting the die ready, filling, cooling, and ejecting. At each stage, the surface quality and number of holes change. To get rid of gas pockets and cold shuts, make sure the melt is clean, the die temperature stays steady, and the fill speed is tracked. Better than high-pressure casting, low-pressure casting lets the metal rise slowly from the furnace instead of splashing in. This keeps the metal from getting too much turbulence and oxide inclusions. After the ejection, the gates and risers were cut by workers. Following that, the part is heated, CNC-machined, finished, and checked. Dimensions are checked, the work is looked over, and it works properly at the end of the process. Leak tests are used to see how well a part can hold air.
Decisions you make about design can change value, cost, and lead time. Keep the width of the walls the same as much as possible. The walls can shrink and twist when things change quickly. Pieces should be slowly put together when making thin shells, like robot housings. Ribs should be added instead of stronger walls. Corner files help the metal flow and spread out the stress. The part can come out of the die clean with draft angles. Plan the fix points, closing faces, holes, and threads for CNC cutting, and make sure the sides have enough stock on them. When you use tight limits, make sure they are needed for the job. Tolerances for as-cast parts are not the same as tolerances for machined parts. Specs that are realistic help keep quotes honest and cut down on the number of rejections.

Aluminum, silicon, and magnesium are mixed together to make A356. A little over 7% of it is silicon, and 0.3% is magnesium. The magnesium in the combination makes it stronger through T6 heat treatment, which is a mix of solution treatment and making the metal age artificially. Since the material has silicon in it, it is easy to fill. A356 doesn't rust and fits together well. If gas gets trapped in parts during heat treatment, blisters can form. This is why high-pressure die cast parts usually skip T6. On the other hand, it works better for low-pressure and permanent mold parts. Asbestos isn't always easy to find or buy, so make sure you write down the exact measurements on the plan. You should ask for material certificates for each heat lot.
As-cast surfaces have gate marks, splitting lines, and some differences in how they look, so don't be surprised by them. The surface is cleaned and left with a smooth, matte finish that hides small scratches when you shot blast something. It's on our robot's body. You can tumble, brush, and polish some styles to make them look better. Paint, powder coating, anodizing, and conversion coating can all be used to protect something or change its color. However, they all respond with metals that are high in silicon in different ways. Take A356 that has been polished as an example. It looks grayer than low-silicon metals. Before you buy the whole thing, feel a small piece of the coating. Making mating faces, bores, and threads on a CNC machine is a great way to make sure that the part is flat and in the right place.
There's no one way that always works. One-of-a-kind aluminum die cast prototypes and design changes that happen a lot can be made with CNC cutting from billet. However, shell forms lose material and the cost goes up as the part gets bigger. Cast metal has a different microstructure than metal that is 3D printed. This is helpful for early studies of shape and fit. Because the tools are so cheap, sand casting can be used to make bigger and thicker parts. With permanent mold casting, you can make surfaces that are better. When you need thin walls, built-in bosses and ribs, precision, and a clear way to add volume, die casting, even low-pressure casting, is a good choice. When the idea is strong enough to need a tool, pick it.
The cost of casting is only a part of the whole. It costs a lot to ship, finish, check, guess the size, weight, number of cavities, design of tools, and run a machine. A 16.7 kg robot shell costs more to make than a small bracket because it takes more time and metal. CNC cutting can help a lot when a lot of faces need to be very close to each other. Get a quote from each supplier that breaks down the costs of shipping, making the tools, casting, machining, finishing, inspecting, and making the product. With that list, you can look at different deals that have the same terms. It also shows where the total would go down if the design was changed, for example by having fewer machined faces.
It's cheaper and faster to get prototype tools, but over time, they might not make parts that are as uniform. Bridge tools are in the middle. They help with engineering batches while you finish validation. The most expensive tools are the ones that are used the most. However, when bought in bulk, they cost the least per piece and last the longest. Which one you pick will depend on how many you need this year and how well the design fits together. Better yet, use a less expensive tool to make the changes that are still possible. It's cheaper to go straight to production-intent tooling because you don't have to pay twice if the design gets stuck.

Three habits that help keep project prices low:
These habits will help you not go over your budget and set goals with enough time to reach them.
In real life, this is what low-pressure casting can do. Rongbao Enterprise uses low-pressure casting to make the shell of a robot out of A356 aluminum. It weighs 16.7 kg. CNC cutting is used to finish the important parts, and shot blasting is used to treat the surface. We can change the specs to fit your needs, and we're happy to work on both OEM and ODM projects. With our base in Xi'an, China, we can make up to 5,000 pieces at once, and they are shipped out in boxes from there. The plant has ISO 9001:2015, ISO 14001, and ISO 45001 certificates. Precision machining, mold making, high-pressure, low-pressure, and gravity casting, as well as surface treatment, are all things we've done for 20 years. This means that one group can work on a project from the planning stage all the way through to the end result.
The first thing you should do is show proof of process control. ISO 9001:2015 is about managing quality, ISO 14001 is about managing the environment, and ISO 45001 is about managing health and safety at work. You should be able to keep track of the materials used and see records of the sizes of the first things that were made. An honest supplier should tell you about any risks in the wall thickness, porosity, parting lines, and machining datums before they give you a quote. If you want to sell to people in other countries, you should also talk about your export experience, technical English, reaction times, and how your drawings will be kept secret. This company's goods are mostly bought and sold in Europe, the US, and Japan. This is why our team is used to selling papers and taking orders from people in other countries.
It's easier to answer quickly when your questions are clear. Send 3D CAD files, 2D drawings, the alloy and heat-treatment needs, lots, tolerances, surface finish, testing standards, packing needs, where you want to meet, and the dates you want to do it. Ask the seller to look over the project to see if it's possible before you compare quotes. Before releasing the tool, make sure that the revised model, metal, parting line, inspection standards, and terms of tool ownership are all okay. Before making any changes, make sure you agree with the piece. Then help with orders that run over. When you need a material that is similar to the real thing, thin walls, built-in features, and the ability to make a large number of them or a small number of them, aluminum die cast prototypes work best. If the part needs to be changed quickly, is very big, or has holes that need to be filled and have tight pressure integrity, a different process might work better.
A way to make metal parts is to die cast them. Each part has its own best way to do it. A high-pressure die cast is the best way to make thin, big parts. It's easy to use A356 in low-pressure casting, and it can handle T6 heat treatment, which is good for structural shells. Teams can try production-like material with aluminum die cast prototypes, but the results rest on how well they plan a good gate and parting line, how accurate their tolerances are, and how well they CNC machine key faces. Die casting is better than CNC cutting, 3D printing, and sand casting when the plan is set and a lot of parts need to be made. Not just the price of the casting, but also the cost of the work, the finish, the check, and the shipping. Good suppliers stand out from the rest because they have certifications, can track items, and give clear quotes.
Die cast" is the correct form, as in "a die cast part." Yes, aluminum does work well. A lot of people are still looking for "die cast."
For what reason are as-cast tolerances different from changed tolerances? These are the limits that are set by the die and the process for as-cast parts. They depend on the size and shape of the part. CNC cutting makes important faces tighter, like fixed surfaces and holes. You should only set strict limits when the function needs them.
Aluminum die cast prototypes can be used to treat building blocks that need it, like shells and housings. Thin, many-part pieces that are cast under high pressure work best. Your drawing and amount will help an engineer figure out how to do it.
What kinds of finishes are there for surfaces? Most of the time, people choose to paint, powder coat, anodize, brush, tumble, or convert the metal. What kind of alloy you use changes how it looks in the end.
What alloys do you need, how much do you need, any tolerances, what finish do you want, and when do you need them by? We will look over your design and let you know if it is possible. Our company has been making aluminum die cast prototypes for 20 years and has quality systems that are ISO-certified. We can also do everything from mold development to CNC cutting and shot blasting. Send an email to steve.zhou@263.net or zhouyi@rongbaocasting.com with more information, or visit rongbaocasting.com.
Learn about our latest products and discounts through SMS or email